欧美日韩国产一区二区三区地区,亚洲一区二区三区欧美,欧美成人ⅴideosxxxxx,亚洲国产一区二区三区

<br />
<b>Warning</b>:  Use of undefined constant wp_title - assumed 'wp_title' (this will throw an Error in a future version of PHP) in <b>/www/wwwroot/m.zionsfiction.com/wp-content/themes/onii/header-pc.php</b> on line <b>27</b><br />

安裝說明VIEWS

SHA型可調阻尼彈簧減震器安裝說明


來源:http://m.zionsfiction.com/1360.html 發布于:2019-06-24 03:07   瀏覽:5,164

SHA型可調阻尼彈簧減震器安裝說明
SHA?spring isolator installation guide

安裝前,請確認淞江集團彈簧減震器的型號和規格是否正確。
Before installation,make sure the model and the specification are correct.
安裝說明
Installation guide
所需工具:公制口徑17mm(M10)、19mm(M12)開口扳手、爪式千斤.。
Required tools:17mm(M10)、19mm(M12)open wrenches and claw jack.
可先放置與彈簧減震器高度相同的臨時木塊與設備安裝處,再安裝設備。(如圖1)
Place the wooden panel with the same height as the isolator at the installation before installing.(Fig 1)
先將固定螺栓的上部螺帽取下,再放松下部的螺母使全牙螺栓下降,以方便將彈簧減震器放入安裝位置。(如圖2)
Rrmove the upper nuts from the fixed bolt.Loosen the lower nuts to descend the full-thread bolt to install the isolator.(Fig 2)
根據螺栓固定孔的位置,與安裝位置預埋基礎螺栓。
Embed foundation bolt according to the location of bolt-loaded holes.
將彈簧減震器放置到與設備的正確安裝位置。(如圖3)
Place the isolator on the correct installation location.(Fig 3)

SHA型可調阻尼彈簧減震器安裝說明

SHA型彈簧減震器結構圖:
SHA Spring shock absorber Structure drawing
SHA型可調阻尼彈簧減震器安裝說明

型號/規格 L
(mm)
L1
(mm)
L2
(mm)
L3
(mm)
H
(mm)
D
(mm)
M
(mm)
SHA-S 153 123 105 71 120 12 12
SHA-M 178 135 117 76 135 12 14
SHA-L 209 175 1152 88 160 16 16

調整下部螺母使全牙螺栓上升至與設備安裝處,并將上部螺母與全牙螺栓鎖緊。(如圖4)
Adjust lower nuts to raise the full-thread bolt for the installation and slightly lock the upper nuts and full-thread bolt.(Fig 4)
使用開口扳手以順時針方向調整螺母使彈簧受力下壓,調整至臨時木臺可取出時停止調整。(如圖5)
Apply open wrench in the clockwise direction to press down the spring. Adjustment can be stopped and wooden panel can be removed once you can take out thepressure pad.(Fig 5)
將固定螺栓確保完全鎖緊,即完成淞江集團彈簧減震器安裝調整。(如圖6)
After the adjustment,lock the isolator with fixed bolt.(Fig 6)
安裝后請檢查彈簧下壓量,如彈簧壓到底,則表示荷重不足,沒有減震效果。應該更換較大荷重的彈簧減震器型號,并請于本公司業務人員聯系。
After the adjustment,check the press amount of the spring.If it appears with insufficient loading,please replace with bigger loading by contacting our staff.
安裝時 請注意安全。
Be cautious during the installation.

保養須知:每月要觀察CS固定螺栓是否有松動,保持彈簧減震器安裝時彈簧下壓撓度是否正常。
Maintenance checking points:remain M12 fixed bolt locked,balance of the base,installation of the isolator,and the deflection of the spring.

圖1)安裝設備時先放置與彈簧減震器高度相同的木臺。
Fig 1)Pace the wooden panel with the same height as the isolator at the installation before installing.
SHA型可調阻尼彈簧減震器安裝說明

圖2)固定螺栓的上部螺帽先取下來,再把下部螺帽松掉使螺栓下降,以便安裝。
Fig 2)Remove the upper nuts from the fixed bolt.Loosen the lower nuts to descend the bolt for the installation.
SHA型可調阻尼彈簧減震器安裝說明

圖3)將淞江集團彈簧減震器放入設備的安裝底部位置。
Fig 3)Place the isolator on the correct installation location.
SHA型可調阻尼彈簧減震器安裝說明

圖4)調整下部螺帽使螺栓上升至能與設備連接,再將固定螺帽鎖緊。
Fig 4)Adjust lower nuts to raise the bolt to connect with the equipment and slightly lock the fixed nuts.
SHA型可調阻尼彈簧減震器安裝說明

圖5)用開口扳手以順時針方向調整螺帽,調整*臨時木臺可以取出時即可停止調整。
Fig 5)Apply open wrench in the clockwise direction to adjust the nuts.Adjustment can be stopped once wooden panel is removed.
SHA型可調阻尼彈簧減震器安裝說明

圖6)將固定螺栓與設備完全鎖緊后,即完成淞江集團彈簧減震器安裝調整。
Fig 6)After the adjustment,lock the isolator with fixed bolt.
SHA型可調阻尼彈簧減震器安裝說明

點擊下載:SHA型可調阻尼彈簧減震器安裝說明










最新推薦:
  • ·整托盤的彈簧減震器發貨現場“新工廠”
  • ·【NG】K16S-40橡膠接頭“擠壓機”
  • ·【北京搜寶商務中心項目】雙球橡膠接頭合同
  • ·【生產現場】生產車間 自動化 可追溯 5S管理
  • ·【技術】住院部制冷機組隔震示意圖
  • ·【檢測中心】DN400波紋補償器水壓檢測
  • ·KWT型 90度橡膠彎頭
  • ·【樣冊P30】可曲撓橡膠接頭應選擇蝶閥專用法蘭
  • ·【杭州可靠智能工廠暖通項目】減震器合同信息
  • ·南通工廠上班第一天進行全面培訓
  • 主站蜘蛛池模板: 呼伦贝尔市| 峨眉山市| 娄底市| 黄石市| 巩义市| 新源县| 乌鲁木齐县| 老河口市| 中西区| 马山县| 保德县| 横峰县| 石景山区| 嘉兴市| 会理县| 乌海市| 安丘市| 山西省| 辽阳市| 娄底市| 南陵县| 孟州市| 岢岚县| 通河县| 新巴尔虎右旗| 津南区| 陆川县| 来宾市| 阿拉善右旗| 青海省| 阿克陶县| 蓝山县| 思南县| 于都县| 奉化市| 吴桥县| 郧西县| 平遥县| 出国| 左云县| 丹寨县|